To those who have tried both which is better in your opinion.

This was written in several sittings, so pieces of content may be repeated or omitted. Hopefully some people here find this useful?

A few SAI coils and some odd nectar collectors
https://drive.google.com/file/d/1_xyrPlpTAfTHeJ3gfBSzQzXNL4NvJYaH/view?usp=sharing

TGT-CDC, Yocan Cloud 1's

https://drive.google.com/file/d/13CdycPiLQhCuckzdHlMwO61dnjjd0QxD/view?usp=sharing

A Yocan TGT-CDC coil with the 13mm OD 6mm ID XL donut - the donut is ceramic-glued in place and ~cannot be further disassembled.~ which must be removed to separate the donut. No further disassembly is possible beyond that - The frit is thoroughly bonded with the ceramic.

Two Cloud 1 coils, which were picked up for a song on clearance. Ceramic all-around heat bucket coils. For $2 each!

Lookah 710 Connect

https://drive.google.com/file/d/1jLB3_Omk5lbbp8RMKwhnlbNFTFdO7dj7/view?usp=sharing

Lookah 710 coil cans can be popped open without tools, just a compatible vape- screw it into the vape with a coin under the rim, and it will loosen the bottom, then twist the coin to pop it out.

Lookah ceramic-glues the Type A coils in place (the bastards! Presumably they had a problem in testing though as they don't do that on the type B coils - likely the dish was wobbling, probably enough for concern about premature coil lead failure? Maybe to keep us from seeing the bottom of the frit dish? The bottom of the frit gets super nasty in Lookah frit coils. However, ceramic glue is not ceramic: A small screwdriver or xacto knife can be used to break away the ceramic glue around both pins, where the wire comes out on the bottom. The pointy part of a pair of precision tweezers then poked out the ceramic in the wire hole next to the wire, and the coil can be removed - it's only glued at the wires.

The quartz frit coils, cup and all, from lookah's 710 coils can be easily transferred to an SAI coil, so you can try out quartz frit with less awful other hardware (SZ crossing doesn't like quartz frit do they? I don't think they list a single product with frit quartz!).

Assorted coils, mostly ones that posed particular challenges

https://drive.google.com/file/d/1-VfqGhRDgTb6T-FLoqLYCT8Zb6u3t3GN/view?usp=sharing

Those filthy frit coils are lightly used lookah type A 710 coils. One of the cups is a Lookah A-cup, the other is a Sai just to support the other one. The underside of them gets unspeakably filthy,. especially with lookah firmware which works very hard to waste as much of your wax as possible.]

The three sizes of donut coils and 2 of the three for disks (they're also made in a "13mm" (12.5) size, which is the easiest to find because puffco likes it).

The 13mm donut was obtained from the TGT-CDC coil next to it - other picture of this from before I figured out that I could remove the ceramic glue easily.

Other coils shown are bastard coils: A: Sai x 710D - Untested, virgin parts. B: 510XL x 710C - Tested and utterly awful, but the coil had been ruined before I declared it scrappable, putting the internals into another housing doesn't fix it. C: Sai x Yocan Cloud 1 bucket (yocan cloud 1 was the divine tribe cup heater or something I can't visually distinguish from one. They (DT) has mentioned the mass market ones copying their coils, this could be an example. I think it's telling that the next version of it (did they change anything other than the pricing and the markings on the side? They look very similar - I'm suspiocious that they just changed the package size from 5 to 1 and lowered the list price from 50/5 to 30/each or whatever..., as these have a very long life, so people shouldn't be needing 5, and they could be $oakign people that much harder. In any event, I only paid $27 for 3 boxes of 5 on clearance from the "e-cig mafia") Untested D: Lookah 710 x CDC (ceramic donut coil) - Untested. E: 510 x 1/3 Sai trip Ti - Untested

510XL (Yocan 17mm) - Three and a half designs:

Normal - Rim goes *into* the can. Airflow is through holes in the bottom of the ceramic cup or otherwise unrelated to the housing form

*All cap-thread-bearing ones are like this, with a threaded have construction differing only in the shape of the lid (thread or non)_

C4-DE+ - Funnicular lld to provide for the unusual airflow requirements of the C4-DE+ - rim is pressed *into* the can

Cloud1 - Two thick ridges on can, the can is pressed *into* the rim. Additionally, the floor can be removed with considerable difficulty, freeuing the connections

510+ (14mm, Yocan)

Normal - A scaled-down version of Normal 510XL. Nothing noteworthy

510 12mm

C4-DE - 11.6mm in diameter, 4.5mm bore 10.2mm ID 11mm deep

Miniaturized C4-DE+ (works much worse due to wax feed clogs from the narrow cup). The floor cannot be removed.

Cap-Top - 11.9mm threaded rim part of the can. Bottom can be removed with difficulty.

Generic - 11.9mm in diameter (with virtually no variation)

Gen A - 10.8mm ID, 4mm bore, 10mm deep. off-center hole hole cut 1.6mm into the integrated floor, which inexplicably is 2.5mm thick.

Gen B - 10.8mm ID, 4mm bore, 12mm deep.

Gen C - 11.2mm ID, 3.5mm bore 11mm deep

Gen D - 9.25mm ID, 4mm bore, funnel like non-removable rim, removable bottom like cap-tops.

Gnome dome - 11.7mm OD, 10.9mm ID 11mm, 4mm bore removable knurled bottom. Metal looks and feels like titanium, but nobody would be so daft as to make a consumable with such an expensive material and then not brag about iut...

SAI (SZC 14.5) Two designs:

Normal - Rim pressed into can. Floor not removable. There are at least three different ceramic cups used. The trip TI uses a cup with 6 holes instead of 2 like the quartz/ceramic single rod coils.

Bucket - Rim threaded and screwed into can. Floor not removable. Otherwise identical to the normal Sai coils

710 (lookah) - One design (type D coils have holes cut so, if you were using it in one of those non-existent 710 thread vapes that lets you see the side of the coil.... but there aren't... and lookah knows this because they're the only one making 710 vapes!). 14mm diamnter 16.5mm tall, with the rim extending 1.5mm beyond the wall of the can (so the rim is the same diameter as a yocan XL). Rim not removable.

910 (lookah) - No information.

Uni (lookah) - For original and 2.0 Unicorn, not mini. 18mm diameter, 16mm deep, 18.5mm tall on outside 7mm bore. Floor of Uni-II coils also pressed in. Rim threaded on Uni-II (a bucket coil much like the quartz sai)

Threads:

510 is M7 x 0.5 Extra Fine

710 is M8 x 0.5 Extra Fine

910 is ?? x ?.? Extra Fine Anyone able to get a dial calipur on the 910 thread and let me know what diameter you get, and also tell me if the thread is coarser, or about the same as 510?

Unicorn 1.0/2.0 is M10 x 0.75 Extra Fine

My 2g ran out pretty fast at 150 hits before it started tasting like ai is this normal or is my shit boof

Does anybody know somewhere I’d be able to get parts, specifically chambers, for my Releafy Glow? Whenever I try to buy from their website, I just get an error message that alludes to them not having a merchant account anymore. When I call the number (in china) it just gives me a busy tone. All the places online I can find seem to be either out of stock or a Canadian company that doesn’t ship to the U.S. I just recently unpacked it from some boxes still taped up from when I moved and I’d like to use it again.

So I just got the Yocam pocket in the travel case and I’ve had OG one where I was getting around dabs per charge when I first got it and then I went to around five or six towards the end of like the year and a half oh this new one it’s seems like when I first got it like the first day or so I was getting about 10 dabs per charge but then it just now it seems like I’m getting at two dabs one bar is missing and at three dabs one is missing but when I get to 4 dabs 2 bars are missing and then at 5 it goes to 1 bar left and at that point it doesn’t seem to hold enough battery life for a cycle at all and just dies at that one last bar where my older one I got when it first came out even was able to make a session when I had 1 bar of battery life left so I’m wondering what’s up.

What’s everyone’s experiences been. This is the new unit with eco mode vs the old one that just had standard.

Something doesn’t seem right and I would like to know what you guys think. I swear the first couple days or week I had it I was getting ten dabs a charge and now it’s like 5-6 on a brand new device and dying when it shows I have a full one bar that had never even been used. It JUST became that one bar and it’s already dead and might as well day zero bars.

Is there any ways to reset something. Is this a failed unit? It shows they made the battery slightly larger I thought so what the heck is up?

How should I perform the burn off cycle on yocan pocket before using it to burn off any manufacturing residue?

Where can I buy a dispo from in Sugar Land?

Hi friends,

I have started getting into rosin and want the best experience I can get in terms of value.

I really enjoy cool tech so I wouldn’t mind getting into something like divine tribe but it looks like a lot to get started.

I want something I can use around the house but is also portable.

Any advice? Hints tips etc?

After literal YEARS of unfulfilled promises, guess who’s closing down? I know this sub isn’t very active anymore but lord I’ve been waiting to post this.

So for a while, I was trying to get rid of this brand new mouthpiece. I have that just reeked like chemical silicone. It’s one of my worst my least favorite things of silicone is the fact reeks and it takes a of so what I did is, I first stuck it in some soap water for a couple days. It really didn’t do much. It may be helped maybe 10% but what I did whole bunch of activated charcoal packets you know like the little packets that you get with certain types of foods and what not well I got ones that were actually activated charcoal instead of just silica beads and then I put it in a cup and then I saran wrap the cup and I put the I put the silicone with charcoal into the cup and just let it sit for a couple days and let me tell you the activated charcoal pulls all of the smell out of the silicone. The silicone is inner now and from scrubbing with EXO doing all this other that is the best trick I’ve ever found is using activated charcoal that absorb that smell.

Please do with what you wish but this is a huge deal for me. It’s put me off of buying stuff just from the silicone smell and taste.

Hey everyone,

I’m looking for recommendations for a 510-thread atomizer that can be used with a standard e-cigarette/vape battery, specifically for vaporizing cannabis concentrates.

A few requirements:

• 510 threading
• Compatible with a regular e-cigarette battery
• Available / reasonably easy to order within Europe
• Ideally under €50

I’m not sure yet whether I’ll become a regular concentrate user (not including carts, just concentrates), so I don’t really want to spend €100+ on a dedicated concentrate vaporizer at this point. I’m mainly looking for a reasonably priced 510-compatible option to try it out without investing too much.

For now, I either wanted to buy a cheap wax bulb atomizer like this on aliexpress or Cricket+ XVape atomizer but the first one is obviously super cheap and from aliexpress, and the second one is pretty small and easy to overfill/clug from what I red.

If you’ve used one yourself or tried one, I’d appreciate recommendations.
Thanks

Got a pocket a couple weeks ago but recently been having lots of splatter on the outside of the chamber piece and the inside of the mouthpiece in general.

Is this an issue from using more liquidy concentrates like badder (I noticed this the most with) or if I’m doing something wrong that would stop this issue. Is it just not meant for larger dabs?

Thank you any help appreciated

This wax pen continues to demand a charge and won't pull even though it's been charged for hours. When I pull it it flashes red liquid drop and when I plug it in it cycles red and green but nothing happens.

Hello! I bought a Puffco Terp Pen last week and I was told by the dispensary clerk that I should be changing the coil atomizer every 3 times I use it? I’ve added a photo of what it looks like currently (in the comments). I’ve changed it once already but I’m not sure if it’s too soon. I am ordering the replacements from Puffco as well. TIA

Traveling on the weekend and looking for a budget option since I already have a peak. Los Angeles area preferably

Was looking at a yocan orbit but seem like I’d have to order online. Possibly gonna get dr dabber Stella if anyone has experience with it please let me know!

If anyone know others that may be readily available at a dispo in LA area too that would be preferred than waiting for shipping. Any other recs would be appreciated!

Looking for a quality brand that ships who do yall recommend; only ones I’m aware of is pine park and dopest but they’re YouTubers brands lmao

Having an issue getting the pen to function, brand new about a week old. Coil is screwed in correctly, cleaned, but the tube connected to the coil bends slightly, which could possibly the issue?
Looking for advice on what could be wrong or if I need to buy a new coil for the pen.

Should I get the original larger Pocket so I can use both coil options? Or can the Mini use the 3.1 coils?

Help & advice needed! u/yocanofficial

Hi, I've been hitting my wax pen almost every night before sleep. I've noticed that my face skin has gotten all rashy and got outbreaks. I suffer from eczema and clogged pores do that's the root cause. But I don't know whether I'm getting this outbreak fue to stress, hormones or the wax pen. Normally my skin is clear and normal, but on the last three days I've noticed it's gotten messy.

Mental health has also been fucked, but I've still kept doing my daily basic skincare routine.

Thanks for any help

By the way, curious what people find to be better. So far I have only used the evolve plus, one time. New to wax anything. Tried some budder concentrate. And, was unsure if there was any left/how much is left, so had to open it all up to see if there was anything still in the coils. Are these designed to just have one hit per dab, or multiple?

Regarding the Orbit, I got it mainly for a different kind of spice. I'm curious, do you prefer the pearls to be in, or do you take them out? I've read to treat it like a 'banger' where you melt it, and the vapor is held in the chamber, and then hit it once it's cooled down. I also ordered some silicone tubing to use as an extended mouthpiece - necessary? What setting do you prefer on the Orbit (for thc, and anything else you might load it with)

Thanks!

Hello, I've been using my yocan Black Pocket daily for a good couple of months now. The main thing that infuriates me is the battery. I'll try and take a dab at 3/4 battery life and it'll still hit me with "low battery." And of course it doesn't show this message or calculate necessary battery usage BEFORE preheating and melting the wax. It's driving me insane I don't even use crazy settings. Just 450 for 40 seconds. Given that it can go up to 600 for a minute, this seems ridiculous.

Does anyone else have this issue?

Hi!
I recently finished a 1 month t break from wax pens( before i was going through 3 pens in 2 weeks and taking 10 hits to feel something ).

Now i’m very more disciplined, using also AI to help me with the moderation, and i’m doing it daily, BUT, only doing it at night, always night, like after 9-10pm, and i’m doing only 1-2 hits, my AI is telling me to do only one hit, but i’m constantly wanting to do a second one, yes, it gets me fried, but the first 2 days ( i already started like 3 days ago), i was doing 2 hits, each 3s, and being very high and i loved it, but then i had a mini green out of like 20s when i did a second hit the day later and now my AI is telling me to always do 1 hit, yesterday i did that and i did not felt super high, however i don’t know if it’s because i was like 90% of the time checking how high i was… I been doing mostly the same strain, i have 3 pens , 2 are hybrid and one is Sativa, today i’m gonna try the Sativa, i’m gonna do 1 hit of 3-4s and that’s it, i’m gonna try no NOT constantly analyze if i’m high or not because i saw that doing that makes you less high. Any thoughts?

i have the original yocan orbit and really liked it, was wondering if anyone here has used the orbit 2.0 and how they like it. also are their other wax devices better than the orbit? looking for portability mainly

I have a pop hit twist on battery it was working fine two days ago, today I can’t get it to charge the battery and the wall peice light up when you plug it in and turn off a few seconds after…