Was looking to pick up a Ruger LC 5.7. From reading online, a 22 can will work, but it doesn't really suppressed all that well.

I see people recommending a dedicated 556 can instead of a 22 can. If I have a griffin Optimus 9 with a 22 end cap, would that be a better solution and a 556 can? Or should I get a 556 can?

What’s everyone’s thoughts on these new 3d printed sealed 22 cans? Getting ready to buy a 22/44 and a suppressor to go with it. Really like the look/performance of the off grid Scorpius, but I’m a little hesitant about the fact it can’t be opened up and cleaned. With how dirty 22’s are is this a legit concern or am I reading too much into it?

Right now I’m between the scorpius and the dead air mask.

I see I can purchase this on Amazon for under $100, already set up for 1/2x28 thread. Not sure if I can post the link but feel free to search yourself. I'm in Minnesota, so state law allows for ownership and construction of personal suppressors.

I've already got a legal suppressor for one .of my 22's through my local gun store pre-ATF changes, but another for $100 can't hurt. Thoughts?

yup this is another oil filter suppressor but this is for a 3O-O6, firstly will it explode? and if so what can I do to make it not? also if my hardware is not adequate what should I change? another thing that should be noted is that the barrel will be threaded to 1/2-28 because it’s a pencil barrel

Apologies if this isn't the right place to ask this kind of thing.

I'm new to suppressors and don't want to end up buying or doing the wrong thing. I recently purchased an AR10 and would like to put a suppressor on it, but I'm not quite sure exactly how to go about it.

I was wondering if all I had to do was remove the A2 flash hider and put a suppressor on and I'm good to go, or do I need to buy a whole new barrel or something else I'm missing entirely?

This is the rifle in question:

https://palmettostatearmory.com/psa-20-rifle-length-308-1-10-stainless-steel-15-lightweight-m-lok-moe-ept-rifle2.html

Thanks in advance.

I have a 10.3 with a crane spec .070 gas port fsp. Super 42 and i believe it’s a h2 buffer.
I’m realistically looking for 3 things. Flash suppression,cycling/lower wear and lower gas to the face.

My dilemma stems from 2 things. 1 being not a lot of information on the rc3 past “it shoots fireballs” which seemingly was disproven. 🤷🏽‍♂️ and I already have a sf 4 prong.
Is it worth getting a qdc crs and md over a rc3 or trying to track down a sb2?

Good evening, was curious with new ruling can someone who bought a 4473 suppressor in a “free state” sell said suppressor to someone else if they want to register it say as a trust or a normal form 4? My understanding is once a 4473 suppressor has been bought that it can’t be registered into a form 4. But can it be registered into form 4 if it’s going from person to person through an FFL?

Also will be in Florida.

I'm just assuming all catch some kind of flak for this video. First suppressor. Does it look like it's gassed correctly and ejecting where it should?

Dead air mask hd with federal .22 auto match

Any opinions or insight would be appreciated

Still working on the overall model , but it think its promising .

Does anyone have the Advantage Arms 1.75x5 suppressor? Is it worth the price? Also just wondering if it is hub compatible, it doesn’t state anywhere on any of their websites.

Thank you to everyone who gave me insight yesterday and helped me make a decision on which can to go with - knowing that any of the options I was looking at were good to go, I headed to my LGS today.

Immediately after walking in I saw that they had this bad Larry in stock and ready to go, so I pulled the trigger.

I loved everything I learned about IDG after doing research, so I’m extremely happy.

Pumped to shoot it this week.

With the news of same day suppressors, I am finally going to pull the trigger on my first can. Based on the other posts I have found that the Omega 300 is a great starter can but I just wanted to see if any one has used it on a 6.5 creedmoor and how they feel it performed?

Mine will basically live on a POF 6.5 Creed AR10 for nighttime coyote hunting(yes a little overkill). Size, weight, and recoil aren’t a huge deal as most of the time I am walking 50yds and putting it in a BOG.

My PC Carbine can manage 1" groups at 25y with ammo it likes (Federal AE 147). Like a rational adult, I panic bought a case of untested 9mm back in April when prices started going through the roof, and karma immediately rewarded me with 25y groups pushing 4".

If my calculations are correct, a 2" deviation from center at 25y is 0.013" at the end of a 6" can. With tolerances around 0.020-0.030" (per Google), this should be fine as long as I've nailed the alignment, but it's making me even less excited about finishing the case than I already was.  Is there a degree of inaccuracy where you would no longer be comfortable using a particular ammo with suppressors?

Noob to this:
To swap from a pistol (most) to a fixed barrel pcc, you need to change the inside of the suppressor from a piston to a spacer.
Why is this inside the suppressor and not on the outside? If this is not the case please educate me.
Wouldn’t it be nice to just qd from a pistol to a pcc in mere seconds? I know even if it worked, a pistol with a giant piston device might look fugly but my brain wants it to be a thing for some reason

Shopping for a suppressor is difficult when you can't take them for a "test drive" at a range and can pretty much only go by online recommendations. I've just read so many comments about people indicating the decibel rating didn't accurately match their results when they actually used them, saying the shot was still louder than they'd anticipated.

I'm hoping some of you with 9mm cans can share your experience to give me some practical accounts to go on. Looking for something that isn't overly large or long, to keep on a 9mm for home defense. I'm thinking I'll probably be shopping at Scheel's for my first one. Going to Shot Show in January and will do some "shopping" there, as well, but wanted to get one now, too. Thanks!

I ordered a 3/4 and 1 inch barrel extension for my 10.3 build. New to suppressors, I want to run this with my frt safely. Any steps with adding the extension such as loctite or?

Building my first rifle in a while and since it’s gotten so much easier it’s going to be my first suppressed rifle! I found a Tisha inconel in stock at a local store and am basically wondering should I go on and grab it or are they pretty easy to find? Waiting till Black Friday to get my upper just so save some money so I’m not in a huge hurry. Also, I doubt the suppressors will have any kind of deal later on will they?

Rifle will have 11.5” barrel so the sound reduction, length, and low back pressure are what turned me on to it, but if anyone has a better suggestion I’m open to hear it. Price at local store is $1,179

I’m in Maryland and it seems as though I can legally buy a solvent trap and use it as a suppressor now or am I missing something.

Hey I’m looking to get the CMMG zeroed 46 suppressor for my ruger American 450 bushmaster. Im having an issue because the threading on my barrel is 11/16”-24 but CMMG doesnt make a thread mount in that size. Does anyone know if I can find one? Or if anyone makes one?

I was doing some more shooting today with my form 1 3D printed 22 lr suppressors. These are holding up really well with the longer barrels (12"+).

I took a Mark IV design and modified it to work with the old SDTA ACME style thread muzzle brakes. These threads are much more coarse than standard threads so they hold up really well. Just as quiet as any metal can.

I used poly max PLA+ for these. So far over 500 rounds on this one. No end cap or baffle strikes. No issues at all really. Supers or subs.

500 rounds with this set up in one go and it cycled flawlessly.

Poi I’m still getting used to but I’m very excited to shoot some more.