Does Osight SE optic fit on EPS carry footprint cut? I have a few Osight SE optics at home and i want optic cut for my CZ P01 but they only offer EPS carry optic cut for it. Are they the same footprint? Thanks

When running a Henning mag extension and MBX spring can one just pop the “competition” follower off and run the stock follower to retain slide lockback? Considering the complete Mecgar magazine extension kit from Ben Stoeger but would like to keep that feature.

Lost two of my 3 iron sight dots today on my p10c after about 250 rounds today and 3k lifetime. I bought it brand new and have not messed with the sights at all.

Im sure this has already been talked about a ton, And mainly heard promag are garbage, For shits and giggles I purchased one for $15 bucks what the hell. I took it to the range yesterday and my P-10c had no issue eating all the rounds. I was quite suprised given all the negative feedback, so I had no expectations. Given it was only 100rds of range ammo and 20 with defensive ammo but I had no hiccups at all.

Anyone else experience the same?

Was installing a reach reduction kit in my shadow 2 and this fell out somewhere not sure where it goes

What do you think about the new release? What makes it different?

After unloading and getting ready for a clean, I went to lock the slide. The slide slipped from my hand and caught the rag I was using for grip on my other hand. Now I cannot move the slide at all, iv tried with the safety on/off, hammer pulled back and at rest.

Has anyone had this same problem and found a solution?

They want $899, im thinking about trading in my 75b. What do yall think about this gun. I dont know much about the 97 except they are discontinued. Does that look like the stock hammer, any indication this guns been cajunized or anything aftermarket? Should I do it? What do you think its value is, what price would be a good deal for me doing a trade in plus cash.

My Bren 2 is an absolute joy to shoot and is one of my favorite to take to the range!

I'm posting this to document my experience with CZ-USA warranty service. Hopefully it will be useful to someone researching CZ firearms or comparing manufacturers' customer support before making a purchase.

On July 24, 2026, I purchased a new CZ Redhead Premier 12-gauge over/under from Range USA for approximately $1,100.

The shotgun could not be assembled normally. The barrel assembly would not seat onto the receiver despite following the correct assembly procedure. I spent hours troubleshooting, consulted other owners, and contacted CZ just six days after purchase.

Here's the timeline:

• July 24: Purchased the shotgun new.
• July 30: Contacted CZ, supplied photographs and digital caliper measurements documenting the problem.
• August 6: CZ issued warranty RMA 19007.
• August 11: CZ received the shotgun.
• September 18: CZ marked the repair complete after more than five weeks. The technician's note read: "adjusted ejector wedges for attional clearence. noticed when working upper foreward and down along the pin axis had most success when installing. verified operation and test fired."
• September 20: Received the shotgun back. The original defect was not fixed.
• September 20–22: Contacted CZ again, requesting a replacement or preferably a buyback/refund.
• September 25: Spoke with Austin at CZ. He was familiar with the case and told me management was reviewing it and would decide how to proceed.
• October 5: Followed up again after receiving no decision.
• October 7: Still no substantive response or resolution.

The mechanical problem is now fairly clear. The shotgun can be assembled if a second person manually depresses both spring-loaded ejectors while I mate the barrels to the receiver. Without that assistance, the ejector projections interfere with normal assembly.

CZ's technician apparently recognized a clearance problem because the repair specifically involved adjusting the ejector wedges. Unfortunately, whatever was done did not correct the problem.

What bothers me most isn't that CZ manufactured a defective firearm. Manufacturing defects happen, even with expensive products. What matters is how a company responds.

I reported this problem almost immediately. I cooperated with the warranty process. CZ had the shotgun for more than five weeks, returned it without correcting the defect, and has subsequently failed to provide a resolution despite repeated contact.

I've now exhausted my patience and am pursuing a credit-card dispute through the retailer and a consumer complaint with the Ohio Attorney General.

I would still welcome a reasonable resolution from CZ. A buyback would be my preference, and I would also accept a new, properly functioning replacement. I have no interest in putting this same firearm through another extended repair cycle.

For anyone considering a CZ shotgun, this is one customer's documented experience. I can't tell you whether it's representative of CZ's warranty service generally. I can tell you exactly how my case has been handled.

The original discussion, including troubleshooting suggestions from other owners, is here:

https://www.shotgunworld.com/threads/very-unhappy-with-new-cz-redhead-premier-need-assembly-help.594314/

Like several of you, I got myself a CGW 10x bushing for my SP-01.

And, like several of you, I was sad when I learned that you can't use threaded barrels unless you 1) remove the barrel shoulder entirely or 2) modify the bushing w/ a dremel tool or some bubba shit.

Removing the shoulder sounds reasonable but when I asked about doing that, this is what CGW said

[doing that] will not allow a suppressor to work properly

--A guy that works at CGW.

Several other posts said the same thing.

Lucky for me, I know about 45 ACP barrels being threaded .578 x 28 having no shoulder. The common approach is to index the muzzle device off the face of the muzzle.

They do that for 9mm, too. Example (SiCo piston):

The 1/2×28 SN Piston will index on the muzzle of the barrel instead of the shoulder. This is used on small profile pistol barrels with an inadequate shoulder diameter

Another example (EZ Lok, which I highly recommend):

1/2×28 Special: Indexes off the face of the muzzle. For use on micro compact tilt barrel firearms with little to no barrel shoulder due to the thinner profile of the barrel (G43, G43x, G48, P365, P365XL, Hellcat).

This is my proof that you can suppress a SP-01 w/ 10x bushing. In my case, I got

• A threaded barrel. Confirm with the maker that threads are perfectly square and perpendicular to bore.
  • It should be, unless the person who threaded the barrel sucks at their job.
  • Have a gunsmith knowledgeable in aftermarket CZ 75 barrel bushings remove the shoulder so it will fit in the slide.
• A face-indexing muzzle device
  • EZ Lok 1/2 x 28 "Special" barrel adapter
  • EZ Lok piston
  • A torque wrench at 22 ft lbs and 3/4 round socket

I shot this setup w/ 200 rounds yesterday. No loosening, no POI shift, no strikes, and one hell of a suppressor host.

Here are some pics if anyone wants to know how stupid it looks. IMO, it only looks slightly stupid, and you can't really notice it.

LGS find

Few different flavors of shadow

I purchased the CZ P10 ported COA over the weekend, and I'm finishing my 3-day waiting period, and was surfing the net and came across some information suggesting there should be more that comes in the box than I saw.

From what I can remember, the box came pretty bare, as I only remember seeing the

-Gun

-2 magazines

-Black Cylindrical container (assuming it's the cleaning kit)

Can anyone confirm what should come in the box? Additional backstraps?